AN Hose Ends & Braided Hose by AN Size
An AN hose end is the fitting that terminates a braided hose run and screws onto the AN port, rail, pump or cooler at the other end - and the dash number in its name is its size: the number counts sixteenths of an inch of the tube size the fitting was designed around, so -6 is the 6/16 (3/8 in class) size, -8 the 8/16, and so on. This page sorts 24 in-stock hose ends and braided hoses from Redhorse Performance, Allstar Performance, Fragola Performance Systems and Vibrant Performance, from $6.49 to $61.99, the way the choice is actually made: first by AN size, then by angle, then by hose family - because an end only works on the hose family it was made for. Every series, angle, material and finish below comes from that product’s own listing, and where a listing states nothing, this page says so instead of filling it in. Every order over $200 ships free.
OUR AN HOSE END & BRAIDED HOSE PICKS
| Product | Spec (from the product listing) | Price | Why it is here |
|---|---|---|---|
| Allstar Performance Pushlock Hose End Black Straight -6 - ALL49412 | Straight push-lock end, -6 AN hose barb to -6 AN female, aluminum, black anodized (per listing) | $6.49 | The floor of this page: Allstar’s barb-style push-lock end is the simplest fitting here - the hose pushes onto the barb instead of being trapped by a socket - and it sets up the push-lock shelf below. |
| 6AN Swivel Hose Ends Black STR | 1000 Series, straight, -6 AN hose to -6 AN female, aluminum, black anodized (per listing) | $9.29 | The workhorse pick: -6 is the size most fuel and oil lines on this page are built in, and this is Redhorse’s straight swivel end for it - the reference fitting every other shelf is a variation on. |
| 8AN PTFE Hose Ends Black STR | 1200 Series, straight, -8 AN PTFE hose to -8 AN female, aluminum, black anodized (per listing) | $16.16 | The PTFE shelf’s middle size: a dedicated PTFE end, because PTFE hose takes its own fitting family - this one is not interchangeable with the rubber-core ends above it, and the page keeps the two apart. |
| 16AN Swivel Hose Ends Black STR | 1000 Series, straight, -16 AN hose to -16 AN female, aluminum, black anodized (per listing) | $27.29 | The big end of the straight shelf: the same 1000 Series pattern carried up to -16, the size class of large oil and coolant plumbing - proof the size ladder runs the full page, not just the small sizes. |
| 10ft Roll -6 Stainless S teel Braided Flex Hose | -6 AN flex hose, 10 ft, braided stainless over rubber core, natural finish (per listing) | $61.99 | The ceiling of this page is not a fitting at all but the hose itself: Vibrant’s 10 ft roll of stainless-braided -6, for a car being plumbed end to end rather than one line at a time. |
STEP ONE: STRAIGHT SWIVEL ENDS, -4 TO -16
Six straight ends, all one pattern: Redhorse Performance’s 1000 Series, listed as aluminum with a black anodized finish, sized hose-to-female in the same AN size - -4 ($12.83), -6 ($9.29), -8 ($10.85), -10 ($14.72), -12 ($17.04) and -16 ($27.29). A swivel end lets the nut turn while the hose stays put, so the line can be clocked into place without twisting it - that is what the word buys you over a fixed end. One size warning that applies to every shelf on this page: the dash number is a size class, not a measured bore, and the actual inside diameter differs between hose families of the same dash size - match the end to the hose family first and the dash number second. Questions before you order? Call 213-549-4279 (Mon-Fri, 9am-5pm PT) and we will read the listing with you.
STEP TWO: ANGLED ENDS - 45 AND 90 DEGREES
When a straight end would kink the hose against a firewall, rail or cooler port, the angle is the fix - the fitting turns the corner so the hose does not have to. Redhorse’s 1045 Series covers 45 degrees in -6 ($21.17) and -8 ($22.79), and its 1090 Series covers 90 degrees in -6 ($18.84), -8 ($21.54), -10 ($24.24) and -12 ($26.93) - every one listed as a swivel, aluminum, black anodized, hose-to-female in the same size. The wider range also carries 30, 60, 120, 150 and 180 degree ends; those stay in the parent collection and are named in the note below. The honest way to choose between 45 and 90 is the routing itself: mock the line up, and pick the angle that leaves the hose in a relaxed curve.
STEP THREE: PTFE ENDS ARE THEIR OWN FAMILY
PTFE-lined hose does not take rubber-core ends. The seal and the way the end grips the hose are built for the PTFE liner, so the ends are a separate series: Redhorse’s 1200 Series straights in -4 ($13.46), -6 ($14.17) and -8 ($16.16), each listed as PTFE hose to female, aluminum, black anodized, plus Fragola Performance Systems’ Real Street straight in -10 ($19.99) on the same terms. Two things follow from the family split. First, a -8 PTFE end and a -8 rubber-core end are not substitutes even though the dash number matches. Second, PTFE hose of a given dash size runs a smaller bore than rubber-core hose of the same dash size, so a size that flowed enough in rubber core is not automatically the same flow in PTFE - size the line for the family you are actually running.
STEP FOUR: PUSH-LOCK - THE BARB SHELF
The simplest assembly on this page: a push-lock end carries a hose barb instead of a socket, and compatible push-lock hose pushes onto the barb. Allstar Performance’s straights are listed exactly that way - -6 AN hose barb to -6 AN female ($6.49) and -10 AN hose barb to -10 AN female ($10.99), aluminum, black anodized - and the hose that belongs with them is here too: Redhorse’s 402 Series push-lock hose, -6, 3 ft, rubber, black ($18.42). What this page does not print is a pressure figure for the push-lock shelf, because no listing here publishes one - push-lock is the low-pressure end of the plumbing world by design, and the exact limit for a given hose and end is the maker’s number to state, in the hose’s own spec, before the line goes on a pressurized system.
STEP FIVE: THE HOSE ITSELF
Four hoses close the page, in the two families the ends above belong to. Rubber-core braided flex hose: Vibrant Performance’s -6, 2 ft, braided stainless over a rubber core, natural finish ($13.99) and its -8, 2 ft, braided nylon over a rubber core, black ($16.99) - the stainless braid is the abrasion armour, the nylon braid is the lighter, no-fray option, and both listings state the same rubber core underneath. For a full car, the same Vibrant -6 stainless hose comes as a 10 ft roll ($61.99). PTFE hose: Fragola’s Series 6000, listed as braided stainless over PTFE, in -6, 3 ft ($20.99) and -8, 3 ft ($19.99) - the hose the 1200 Series and Real Street ends in Step Three are made for. Pre-cut lengths are what this page carries; longer rolls of the same families live in the parent Bulk Hose range.
AN HONEST NOTE ON WHAT IS NOT ON THIS PAGE
The parent Hose Ends range holds 1,849 products and the Bulk Hose range 715, and this page is the black-anodized, size-sorted core of them. Excluded: the crimp ends and crimp collars (Earl’s Auto-Crimp collars and the crimp-style ends - a crimped line is its own assembly method, needing the maker’s crimper, and belongs together as a set); the other colours of the same Redhorse ends (blue and clear anodized variants of most sizes and angles are in the parent range - this page standardised on black so the size ladder reads cleanly); the 30, 60, 120, 150 and 180 degree ends and the -20 sizes; the adapters - AN-to-NPT, AN-to-ORB, unions, tees and plugs live in the fittings collections, not here, because an adapter is not a hose end; and the specialty shelves (power-steering ends, brake hose and ends, hose by the spool in other families). Also named plainly: no listing on this page publishes a working-pressure rating, a temperature rating or a thread size, so none is printed here - those figures live in each maker’s own catalog for the exact part number, and they are worth reading there before a line is pressurized.
QUESTIONS BUYERS ASK US
What does -6AN actually mean? The dash number is the size, counted in sixteenths of an inch of the tube size the AN system was built around: -4 is the 1/4 in class, -6 the 3/8 in class, -8 the 1/2 in class, -10 the 5/8, -12 the 3/4 and -16 the 1 in class. It is a size class, not a promise about the hose’s measured bore - PTFE and rubber-core hose of the same dash size differ inside, which is why this page sorts by family as well as size.
Can I put a rubber-core end on PTFE hose, or the other way round? No. The end is built for its hose family - the 1200 Series and Real Street ends above are listed for PTFE hose, the 1000/1045/1090 Series ends for rubber-core braided hose, and the push-lock ends for push-lock hose. Same dash number does not make them interchangeable; match the series to the hose before you match the size.
Straight, 45 or 90 - how do I choose? By the routing, not by preference. A straight end where the hose has to turn hard will kink or chafe; a 90 where a gentle 45 would do adds an unnecessary tight turn. Mock the run up with the actual components, keep the hose in a relaxed curve with clearance from exhaust heat and moving parts, and let that decide the angle - the six angled ends here cover the two commonest turns in the four commonest sizes.
Do push-lock ends need a clamp or a crimper? The design is in the name and the listing: the end is a barb, and push-lock hose pushes onto it - there is no socket to tighten and no collar to crimp, which is exactly why the shelf exists for low-pressure lines. What this page will not do is state the pressure limit for you, because the listings do not publish one; read the hose maker’s spec for the hose you bought before the system is pressurized.
Stainless braid or nylon braid over a rubber core? Both Vibrant hoses on this page state a rubber core; the difference the listings state is the braid itself - stainless in natural finish, or nylon in black. Stainless is the traditional abrasion armour for lines routed near sharp edges and heat; nylon braid is lighter and does not fray into the sharp ends a cut stainless braid leaves. Neither listing publishes a pressure or temperature rating, so for a line near its limits the maker’s catalog, not the braid, is the deciding document.
How much hose should I buy? Measure the routed path, not the straight-line distance - bends, service loops and the length the ends themselves consume all come out of the roll. The pre-cuts here run 2 ft and 3 ft for single lines and 10 ft for a full -6 plumbing job; when a measurement lands between two lengths, the longer roll is the honest buy, because a line that comes up two inches short cannot be stretched and a trimmed offcut is rarely wasted in a race shop.
Shopping the wider range? Browse the full Hose Ends collection, read our guides on the News & Builds blog, or see the page that came before this one: Ring & Pinion Gears by Axle + Ratio.