Ring & Pinion Gears by Axle + Ratio
A ring and pinion gear set is the matched ring gear and pinion gear that set your rear axle’s final-drive ratio - swap the set and the same engine turns the wheels faster off the line or cruises at lower rpm, depending on which way you go. This page sorts 24 in-stock gear sets from Allstar Performance, Motive Gear, Richmond Gear, EXCEL from Richmond, Yukon Gear and Axle and Ford Performance Parts, from $169.99 to $760.99, the way the choice is actually made: first by axle, then by ratio. Every ratio, pinion spline count, carrier series and thick-gear note below comes from that set’s own listing, and where a listing states nothing, this page says so instead of filling it in. Every order over $200 ships free.
OUR RING & PINION PICKS
| Product | Spec (from the product listing) | Price | Why it is here |
|---|---|---|---|
| Allstar Performance Ring & Pinion GM 8.5 3.08 - ALL70120 | 3.08 ratio, 30-spline pinion, 8.5 in ring gear, GM 10-bolt (per listing) | $169.99 | The floor of this page and its street-ratio anchor: the tallest gear here, for the GM 8.5 in axle, at the lowest price on the page - the starting point for anyone re-gearing a cruiser rather than a strip car. |
| 3.55 8.8in Ring & Pinion Gear Set | 3.55 ratio, 28-spline pinion, Ford 8.8 in (per listing) | $242.99 | The Ford 8.8 shelf opens with Ford Performance Parts’ own gear set - the factory performance line for the axle under generations of Mustangs and trucks. |
| Dana 60 3.73 Ring and Pinion | 3.73 ratio, 29-spline pinion, 9.75 in ring gear, Dana 60 (per listing) | $306.99 | The Dana shelf’s heavy-duty anchor: a 3.73 set for the 9.75 in Dana 60 ring gear, the axle this store’s Dana 60 hub page is built around. |
| 4.10 12 Bolt GM Pass | 4.10 ratio, 30-spline pinion, 3 Series, thick gear, 8.875 in, GM 12-bolt passenger car (per listing) | $445.20 | The 12-bolt passenger-car pick, and the page’s clearest thick-gear example: Richmond states both the 3 Series carrier and the thick gear in the one listing, which is exactly the pair of facts a 12-bolt buyer has to match. |
| 5.14 Ford 9in Pro Gear 28 Spline | Pro Gear, 5.14 ratio, 28-spline pinion, Ford 9 in (per listing) | $760.99 | The ceiling of this page: Richmond’s Pro Gear line is its drag-race gear line, stated as such in the listing - a 5.14 for a 28-spline Ford 9 in, priced well above the standard 9 in sets below it. |
STEP ONE: GM 7.5 AND 8.2 - THE SMALL 10-BOLTS
Four sets for the two smaller GM 10-bolt ring gears. Allstar’s 7.5 in set ($169.99) states a 4.10 ratio, a 27-spline pinion and a 3 Series carrier. Motive Gear’s 7.5 in set ($329.99) is its Performance line, stating a 3.73 ratio, a 27-spline pinion, a 3 Series carrier and a 7.5 / 7.625 in ring gear - both diameters printed, as the listing states them. The 8.2 in shelf pairs Richmond’s Excel-line 4.11 ($299.99, 25-spline pinion) with Motive’s Performance 3.55 ($389.99, 25-spline pinion). The 7.5 and 8.2 gears do not interchange - the ring gear diameter in the listing is the first check, before ratio. Questions before you order? Call 213-549-4279 (Mon-Fri, 9am-5pm PT) and we will read the listing with you.
STEP TWO: GM 8.5 - THE WORKHORSE 10-BOLT
The deepest GM shelf on this page, four ratios deep, and every set here states a 30-spline pinion. Allstar’s 3.08 ($169.99) is the street end of the ladder. Motive Gear’s Performance line covers the middle: 3.73 at $312.63 and 4.10 at $309.99, neither stating a carrier series in its listing. Richmond’s 4.56 ($356.99) closes the shelf stating a 3 Series carrier and an 8.5 / 8.625 in ring gear - the second listing on this page that prints two ring diameters, and it is printed both ways here too.
STEP THREE: GM 12-BOLT 8.875 - PASSENGER CAR AND THICK GEARS
Three sets for the 8.875 in 12-bolt, all stating a 30-spline pinion. EXCEL from Richmond’s 3.42 ($220.99) states a 3 Series carrier in its one-line spec listing. Yukon Gear and Axle’s 4.11 ($353.99) is a thick gear, stated in its title and listing - a thick gear is how a numerically higher ratio is fitted to a carrier series that would otherwise need changing, which is why the word matters more than the ratio next to it. Richmond’s passenger-car 4.10 ($445.20) states both: 3 Series and thick gear. Where a 12-bolt listing does not say thick, this page does not call it standard either - it says nothing, because the listing says nothing.
STEP FOUR: FORD 8.8
Three sets for the Ford 8.8 in axle - and a pinion-spline split worth reading carefully. Ford Performance Parts’ 3.55 ($242.99) states a 28-spline pinion in its spec line. Motive Gear’s Performance sets state a 30-spline pinion for both their 3.73 ($327.99) and their 4.56 ($387.99). Both figures are printed exactly as each listing states them; the pinion spline count has to match the pinion flange and yoke you are running, so read your chosen set’s listing before ordering rather than assuming the axle decides it.
STEP FIVE: FORD 9 INCH - STANDARD SETS AND ONE PRO GEAR
Four sets for the Ford 9 in, every one stating a 28-spline pinion. Allstar’s 3.50 ($169.99) is the street end and shares the page floor. Motive Gear’s Performance 4.11 ($369.99) and Richmond’s 4.86 ($465.99) climb the ladder, and Richmond’s Pro Gear 5.14 ($760.99) tops the page - Pro Gear is Richmond’s drag-race line as its listing names it, priced at more than four times the standard Allstar set. The wider 9 in range also carries 35-spline Pro Gears and lightened circle-track sets; those stay in the parent collection and are named in the note below.
STEP SIX: DANA 30, 35, 44 AND 60
Four Motive Gear sets, one per Dana axle, and the only shelf where the listings state ring gear diameters beyond the axle name: Dana 30 4.88 ($231.99, 26-spline pinion, 7.125 in ring gear), Dana 35 4.56 ($231.99, 26-spline pinion, 7.5 in ring gear) and Dana 60 3.73 ($306.99, 29-spline pinion, 9.75 in ring gear). The Dana 44 set needs its own sentence: Motive’s 4.11 ($264.99, 26-spline pinion, 8.5 in ring gear) states reverse rotation in its listing - reverse-rotation sets are cut for high-pinion front-axle applications, and this page prints the listing’s words rather than presenting it as a rear-axle set. If your Dana 44 is a standard-rotation rear, this is not your set, and the listing says why.
STEP SEVEN: MOPAR 8.75
Two sets close the page, both stating a 10-spline pinion - the coarse pinion spline is part of what makes the Mopar 8.75 its own shelf rather than a ratio match with anything above. Yukon Gear and Axle’s High Performance 3.23 ($375.99) is the street end; its listing states no case number. Richmond’s 3.91 ($424.99) states a 489 case in its spec line - the 8.75 was built with more than one centre-section case, and the case is a fitment check on this axle in a way it is not on the others, so the one listing that states it gets it printed.
AN HONEST NOTE ON WHAT IS NOT ON THIS PAGE
The parent Ring and Pinion Gears range holds 341 products, and this page is the single-axle, single-ratio core of it. Excluded: the front-and-rear combo kits (Jeep TJ and JK Dana pairs, GM truck front/rear pairs and the F-250/F-350 pair, $739.99-$1,290.92 in the parent range) - a combo is two gear sets priced as one and belongs to a vehicle build, not an axle shelf; the Quick Change ring and pinions (Richmond, Winters and Diversified Machine sets for quick-change rears, a different rear-end type entirely); the Ford 9.5 in and 10 in Pro Gears ($1,159.99-$1,871.99) and the lightened and AX circle-track 9 in sets; the Corvette-specific sets (1963-79, C5, C6 Z06 and GTO sets, each its own application); and the duplicate listings where the same Excel gear set appears under two vendor names in the parent range - one listing per set is carried here. Install kits, bearings, spacers and fasteners live in their own collections, linked from the parent range. Also named plainly: no listing on this page states a ring gear bolt count, and most state no carrier series - where a series is printed above it is because that set’s own listing states it, and a set with no series printed needs the maker’s guide checked against your carrier before ordering.
QUESTIONS BUYERS ASK US
How do I know which axle I have? Start with the ring gear diameter and bolt count of the cover or centre section you already have, then match it to the axle named in the listing - 7.5, 8.2, 8.5 and 8.875 in are four different GM axles whose gears do not interchange, and the same is true across the Ford 8.8 and 9 in. Every listing on this page names its axle in its fitment line (GM 10-Bolt, GM 12-Bolt, Ford 8.8 in, Ford 9 in, Dana 30/35/44/60, Mopar 8.75 in); if you cannot name your axle, measure first or call us - a ratio-perfect set for the wrong axle fits nothing.
What does the ratio change actually do? A numerically higher ratio (4.10 in place of 3.08, say) multiplies torque at the wheels and raises cruise rpm; a numerically lower one does the opposite. This page prints no rpm or speed table, because the honest number depends on your tyre diameter and transmission, which no gear listing here states. Pick the direction from how the car is used - the shelves above run from 3.08 street gears to a 5.14 drag Pro Gear - and work the exact cruise rpm out from your own tyre size before ordering.
Standard or thick gear - and what is a carrier series? Gear sets are made for a carrier series, and the listings that state one say 3 Series (the Allstar 7.5, the Motive 7.5, the Richmond 8.5 4.56 and both Richmond-family 12-bolts here). A thick gear moves the ring gear’s mounting face so a ratio can fit a carrier it otherwise would not - the Yukon 12-bolt 4.11 and the Richmond 12-bolt 4.10 both state thick gear in their listings. If your set’s listing states neither, check the maker’s guide against the carrier in your housing; guessing this one costs a second teardown.
Does pinion spline count matter if the axle and ratio match? Yes - the pinion splines are what your pinion flange or yoke slides onto, and this page alone carries 10, 25, 26, 27, 28, 29 and 30-spline pinions depending on the axle and the maker. The Ford 8.8 shelf is the proof: Ford Performance states 28 splines and Motive states 30 for the same axle. Match the count in the listing to the hardware you are running.
Is a gear set a complete install? No. These 24 listings are the ring and pinion set itself; bearings, shims, seals and fasteners are install parts, sold in the Ring and Pinion Install Kits / Bearings range, and every listing here closes with the same line: professional installation recommended. Gear setup - pinion depth, backlash and pattern - is precision work, and the listings do not publish setup specs, so this page prints none.
Front axle or rear axle - does rotation matter? On the Dana shelf it does, and it is stated where it applies: the Dana 44 4.11 here is a reverse-rotation set, cut for high-pinion front applications. No other listing on this page states a rotation, so none is claimed for them - if you are re-gearing a front axle, confirm rotation in the maker’s guide for the part number before ordering.
Shopping the wider range? Browse the full Ring and Pinion Gears collection, read our guides on the News & Builds blog, or see the page that came before this one: Mechanical Water Pumps by Engine Family.